Axis Wakeboard Boat Forum
http://www.axiswakeboardboats.com/

Flag Holder for the Tower
http://www.axiswakeboardboats.com/viewtopic.php?f=15&t=3750		 Page 1 of 2
Author:  jdiaz78 [ Sun Jun 19, 2016 9:06 pm ]
Post subject:  Flag Holder for the Tower
I have had a hard time finding a flag holder for my Axis tower. What is the diameter of the tubing? Does anyone on here have a flag holder they purchased that they like? Thanks in advance.
Author:  Boostedsled [ Mon Jun 20, 2016 9:40 am ]
Post subject:  Re: Flag Holder for the Tower
I would also like any information on a good flag holder for the tower.
Author:  simo47 [ Mon Jun 20, 2016 10:33 am ]
Post subject:  Re: Flag Holder for the Tower
I was thinking the same thing
Author:  jdiaz78 [ Mon Jun 20, 2016 6:22 pm ]
Post subject:  Re: Flag Holder for the Tower
Come on, someone has to have a good flag holder!
Author:  ThatGuy [ Mon Jun 20, 2016 8:09 pm ]
Post subject:  Re: Flag Holder for the Tower
I have this on my tower.

http://www.walmart.com/ip/20961495?wmls ... 52&veh=sem
Author:  simo47 [ Tue Jun 21, 2016 9:37 am ]
Post subject:  Re: Flag Holder for the Tower
That thing is pretty ugly but I guess I could put it on the tower for a day or two. What size pole will fit in it? That thing looks like it is just meant to hold a "skier down" flag. If that's the case the receptacle may be too small for what I'm going to need.
Author:  NWilly [ Thu Jun 23, 2016 5:46 pm ]
Post subject:  Re: Flag Holder for the Tower
It took me a year to solve this one. Can't figure out how to post pictures.
Author:  jdiaz78 [ Mon Jun 27, 2016 9:26 pm ]
Post subject:  Re: Flag Holder for the Tower
Anyone with a 2014 or new add a flag mount yet? I can't find anything that will fit my tower. It is just under 3 inches in diameter. Most of the holders are for up to 2.5" and some of them are for 2 7/8" mounts.
Author:  NWilly [ Tue Jun 28, 2016 11:53 am ]
Post subject:  Re: Flag Holder for the Tower
The US flag is 18" x 24" on a 4' pole. The other flag is on a 2' pole and 12" x 18".

I can run at speed with them up. I think they are about the perfect dimensions.

Used all Firestik pieces. Stainless flag holder bolted through the flat arm of the tower. Since the tower is angled I had to fool around with varied SS hardware to get the right pieces and offset the angle to make the flagpole more plumb. The poles screw into the holder. The only think I have to watch is that they will back out so I do a quick single wrap of electrical tape around the base and that seems to keep them from backing off.

Attachments:
IMG_3610.jpg
IMG_3610.jpg [ 77.26 KiB | Viewed 52362 times ]
IMG_3590.jpg
IMG_3590.jpg [ 167.95 KiB | Viewed 52362 times ]
Author:  Senek8 [ Wed Jul 20, 2016 8:12 am ]
Post subject:  Re: Flag Holder for the Tower
I used the kwiktec holders from Amazon, without the plastic liners it comes with. It was a tight fit, but it worked.
Page 1 of 2 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/